***Reduced***Item # UFE-1286   $1,475

Full Image

CTD D45 Double Miter Saw

This machine is in Good Working Condition. This machine has been well maintained.

From Manufacturer's Website:

CTD D45 Fixed 45 Degree Frame Saw

The D45 is popular world wide because of its unique features, low cost and precision. Engineered for higher production, this double mitre saw makes two 45 degrees mitres at one time, saving time and materials. D45's are used by thousands in the decorative arts trade throughout world.

Designed to cut Aluminum, Wood, plastics, composites, aluminum extrusions, plastic extrusions, non-ferrous metals.

Blade Capacity: 10" OD (254mm) ,12'' OD, 14'' OD

Spindle & Pivot: Both mounted on pre-loaded and sealed ball bearings.

Arbor: 5/8 (16mm) with 2-1/4 (57mm) saw collars.

Iron Castings: Saw arm, pivot brackets and table are precision machined and ground with milled slots in table to guide pivot brackets and fences.

Motors & Voltages: 1-1/2 H.P., 3450 RPM with Dual Magnetic Starter.

Table Height: 34-1/2 (88cm) from floor.

Floor Stand: Close coupled heavy gage steel stand completely enclosed with 6 dust outlet. 1200 CFM required.

• Length of stroke adjustment: The D45AX is unique in that the stroke of the machine and the position of the blade above the work can be adjusted to use only the stroke needed to cut a particular moulding or extrusion. Saw heads reverse immediately, on release of the foot valve, thereby saving wasted time and motion.
   
• Production Rate: The D45AX is capable of cycling at one second intervals. However, actual production rates vary with the type and width of material to be cut.
   
• Size: Standard machine, without tables or gages; weight 550 lbs. 46'' wide x 22'' front to back x 51-1/2'' high.
   
• Actuation: Pneumatic foot valve with cover
   
• Air Pressure: 75 PSI with Air Filter/Regulator/Lubricator; includes Auto Drain.
   
• Air Consumption: 1.0 CF per 10 strokes at 75 PSI.

This item can be picked up in Washington or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Kyoshi-WA-3-16-11 $1,500 / 6-29-12 $1,475 s

Sold-6-15-16-Kyoshi    Return Home

***Reduced***Item # UFE-1227   $2,150 Or Make Offer

Full Image

CTD D45A Double Miter Saw

This machine is in Good Working Condition. This machine has been well maintained. It is currently used to cut wood.

Below is information from Manufacturer's Website. Check with Tech Support for any differences between what is being sold and the newer generation machines.

From Manufacturer's Website:

CTD D45AX Fixed 45 Degree Frame Saw

The D45 is popular world wide because of its unique features, low cost and precision. Engineered for higher production, this double mitre saw makes two 45 degrees mitres at one time, saving time and materials. D45's are used by thousands in the decorative arts trade throughout world.

Designed to cut Aluminum, Wood, plastics, composites, aluminum extrusions, plastic extrusions, non-ferrous metals.

Blade Capacity: 10" OD (254mm) ,12'' OD, 14'' OD

Spindle & Pivot: Both mounted on pre-loaded and sealed ball bearings.

Arbor: 5/8 (16mm) with 2-1/4 (57mm) saw collars.

Iron Castings: Saw arm, pivot brackets and table are precision machined and ground with milled slots in table to guide pivot brackets and fences.

Motors & Voltages: 1-1/2 H.P., 3450 RPM with Dual Magnetic Starter.

Table Height: 34-1/2 (88cm) from floor.

Floor Stand: Close coupled heavy gage steel stand completely enclosed with 6 dust outlet. 1200 CFM required.

• Length of stroke adjustment: The D45AX is unique in that the stroke of the machine and the position of the blade above the work can be adjusted to use only the stroke needed to cut a particular moulding or extrusion. Saw heads reverse immediately, on release of the foot valve, thereby saving wasted time and motion.
   
• Production Rate: The D45AX is capable of cycling at one second intervals. However, actual production rates vary with the type and width of material to be cut.
   
• Size: Standard machine, without tables or gages; weight 550 lbs. 46'' wide x 22'' front to back x 51-1/2'' high.
   
• Actuation: Pneumatic foot valve with cover
   
• Air Pressure: 75 PSI with Air Filter/Regulator/Lubricator; includes Auto Drain.
   
• Air Consumption: 1.0 CF per 10 strokes at 75 PSI.

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Joseph-CA-2-4-11 $3,350 / 1-25-12 $2,995 / 8-16-12 $2,895 / 11-13-12 $2,595 / 4-1-15 $2,150 s

Sold-6-15-16-Kyoshi     Return Home

***Reduced***Item # UFE-1228   $2,150 Or Make Offer

Full Image

CTD D45A Double Miter Saw

This machine is in Good Working Condition. This machine has been well maintained. It is currently used to Polystyrene Mouldings.

Below is information from Manufacturer's Website. Check with Tech Support for any differences between what is being sold and the newer generation machines.

From Manufacturer's Website:

CTD D45AX Fixed 45 Degree Frame Saw

The D45 is popular world wide because of its unique features, low cost and precision. Engineered for higher production, this double mitre saw makes two 45 degrees mitres at one time, saving time and materials. D45's are used by thousands in the decorative arts trade throughout world.

Designed to cut Aluminum, Wood, plastics, composites, aluminum extrusions, plastic extrusions, non-ferrous metals.

Blade Capacity: 10" OD (254mm) ,12'' OD, 14'' OD

Spindle & Pivot: Both mounted on pre-loaded and sealed ball bearings.

Arbor: 5/8 (16mm) with 2-1/4 (57mm) saw collars.

Iron Castings: Saw arm, pivot brackets and table are precision machined and ground with milled slots in table to guide pivot brackets and fences.

Motors & Voltages: 1-1/2 H.P., 3450 RPM with Dual Magnetic Starter.

Table Height: 34-1/2 (88cm) from floor.

Floor Stand: Close coupled heavy gage steel stand completely enclosed with 6 dust outlet. 1200 CFM required.

• Length of stroke adjustment: The D45AX is unique in that the stroke of the machine and the position of the blade above the work can be adjusted to use only the stroke needed to cut a particular moulding or extrusion. Saw heads reverse immediately, on release of the foot valve, thereby saving wasted time and motion.
   
• Production Rate: The D45AX is capable of cycling at one second intervals. However, actual production rates vary with the type and width of material to be cut.
   
• Size: Standard machine, without tables or gages; weight 550 lbs. 46'' wide x 22'' front to back x 51-1/2'' high.
   
• Actuation: Pneumatic foot valve with cover
   
• Air Pressure: 75 PSI with Air Filter/Regulator/Lubricator; includes Auto Drain.
   
• Air Consumption: 1.0 CF per 10 strokes at 75 PSI.

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Joseph-CA-2-4-11 $3,350 / 1-25-12 $2,995 / 8-16-12 $2,895 / 11-13-12 $2,595 / 4-1-15 $2,150 s

Sold-6-15-16-Kyoshi     Return Home

***Reduced***Item # UFE-1229   $2,150 Or Make Offer

Full Image

CTD D45A Double Miter Saw

This machine is in Good Working Condition. This machine has been well maintained. It is has a 14" blade and is currently used to cut wood & polystyrene mouldings..

Below is information from Manufacturer's Website. Check with Tech Support for any differences between what is being sold and the newer generation machines.

From Manufacturer's Website:

CTD D45AX Fixed 45 Degree Frame Saw

The D45 is popular world wide because of its unique features, low cost and precision. Engineered for higher production, this double mitre saw makes two 45 degrees mitres at one time, saving time and materials. D45's are used by thousands in the decorative arts trade throughout world.

Designed to cut Aluminum, Wood, plastics, composites, aluminum extrusions, plastic extrusions, non-ferrous metals.

Blade Capacity: 10" OD (254mm) ,12'' OD, 14'' OD

Spindle & Pivot: Both mounted on pre-loaded and sealed ball bearings.

Arbor: 5/8 (16mm) with 2-1/4 (57mm) saw collars.

Iron Castings: Saw arm, pivot brackets and table are precision machined and ground with milled slots in table to guide pivot brackets and fences.

Motors & Voltages: 1-1/2 H.P., 3450 RPM with Dual Magnetic Starter.

Table Height: 34-1/2 (88cm) from floor.

Floor Stand: Close coupled heavy gage steel stand completely enclosed with 6 dust outlet. 1200 CFM required.

• Length of stroke adjustment: The D45AX is unique in that the stroke of the machine and the position of the blade above the work can be adjusted to use only the stroke needed to cut a particular moulding or extrusion. Saw heads reverse immediately, on release of the foot valve, thereby saving wasted time and motion.
   
• Production Rate: The D45AX is capable of cycling at one second intervals. However, actual production rates vary with the type and width of material to be cut.
   
• Size: Standard machine, without tables or gages; weight 550 lbs. 46'' wide x 22'' front to back x 51-1/2'' high.
   
• Actuation: Pneumatic foot valve with cover
   
• Air Pressure: 75 PSI with Air Filter/Regulator/Lubricator; includes Auto Drain.
   
• Air Consumption: 1.0 CF per 10 strokes at 75 PSI.

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Joseph-CA-2-4-11 $3,350 / 1-25-12 $2,995 / 8-16-12 $2,895 / 11-13-12 $2,595 / 4-1-15 $2,150 s

Sold-6-15-16-Kyoshi     Return Home

***Reduced***Item # UFE-1230   $2,150 Or Make Offer

Full Image

CTD D45A Double Miter Saw

This machine is in Good Working Condition. This machine has been well maintained. It is currently used to cut metal mouldings.

Below is information from Manufacturer's Website. Check with Tech Support for any differences between what is being sold and the newer generation machines.

From Manufacturer's Website:

CTD D45AX Fixed 45 Degree Frame Saw

The D45 is popular world wide because of its unique features, low cost and precision. Engineered for higher production, this double mitre saw makes two 45 degrees mitres at one time, saving time and materials. D45's are used by thousands in the decorative arts trade throughout world.

Designed to cut Aluminum, Wood, plastics, composites, aluminum extrusions, plastic extrusions, non-ferrous metals.

Blade Capacity: 10" OD (254mm) ,12'' OD, 14'' OD

Spindle & Pivot: Both mounted on pre-loaded and sealed ball bearings.

Arbor: 5/8 (16mm) with 2-1/4 (57mm) saw collars.

Iron Castings: Saw arm, pivot brackets and table are precision machined and ground with milled slots in table to guide pivot brackets and fences.

Motors & Voltages: 1-1/2 H.P., 3450 RPM with Dual Magnetic Starter.

Table Height: 34-1/2 (88cm) from floor.

Floor Stand: Close coupled heavy gage steel stand completely enclosed with 6 dust outlet. 1200 CFM required.

• Length of stroke adjustment: The D45AX is unique in that the stroke of the machine and the position of the blade above the work can be adjusted to use only the stroke needed to cut a particular moulding or extrusion. Saw heads reverse immediately, on release of the foot valve, thereby saving wasted time and motion.
   
• Production Rate: The D45AX is capable of cycling at one second intervals. However, actual production rates vary with the type and width of material to be cut.
   
• Size: Standard machine, without tables or gages; weight 550 lbs. 46'' wide x 22'' front to back x 51-1/2'' high.
   
• Actuation: Pneumatic foot valve with cover
   
• Air Pressure: 75 PSI with Air Filter/Regulator/Lubricator; includes Auto Drain.
   
• Air Consumption: 1.0 CF per 10 strokes at 75 PSI.

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Joseph-CA-2-4-11 $3,350 / 1-25-12 $2,995 / 8-16-12 $2,895 / 11-13-12 $2,595 / 4-1-15 $2,150 s

Sold-6-15-16-Kyoshi     Return Home

List Price $6, 095 (with dust collector)

Item # UFE-2319   $2,800

Full Image

CTD D20R Double Miter Saw

This machine is in Good Condition.

12" blades

This item can be picked up in Washington State or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Randy-WA-2-9-15/1366

SA-Sold-11-8-16  Return Home

List Price $6, 095 (with dust collector)

Item # UFE-2322   $2,750

Full Image

CTD D45A Double Miter Saw

This machine is in Good Condition.

10" blades

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Joseph-CA-2-17-15/1356

Sold-5-23-16-Joseph  Return Home

Item # UFE-2340   $ Call for Pricing

Full Image

CTD D45 Double Miter Saw

This machine is in Good Working Condition.

220 Volt

This item can be picked up in Kansas or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Lincoln-KS-3-18-15/1380

Sold-6-9-16-Lincoln   Return Home

Item # UFE-2348   $ Call for Pricing

Full Image

CTD D20R Double Miter Saw

This machine is in Good Condition.

This item can be picked up in Texas or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Peter-TX-4-8-15/1392

Sold-7-24-15-Peter    Return Home

Item # UFE-2356   $ Call for Pricing

Full Image

CTD D20R Double Miter Saw

This machine is in Good Condition.

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Les-CA-4-17-15/1408

No Longer Available  Return Home

Item # UFE-2386   $ 1,495

Full Image

CTD D20 Double Miter Saw

This machine is in Good Condition.

Includes sawdust vacuum

This item can be picked up in North Carolina or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Rob-NC-5-27-15/1471

See Page #354 for Current Information    Return Home

Item # UFE-2429   $ 2,750

Full Image

CTD D45AX Double Miter Saw

This machine is in Good Condition.

Includes infeed and outfeed table.

Size:  12"

This item can be picked up in Texas or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Allen-TX-7-29-15/1466

Sold-6-16-16-Allen   Return Home

Item # UFE-2452   $ 4,500 with Holddowns SA-Sold-12-20-16 

Item # UFE-2452b   $ 3,500 without Holddowns 

Full Image

CTD D45X Double Miter Saw

This machine is in Good Condition.

This item can be picked up in Ohio or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Earl-OH-2-19-16/1553

See Page #354 for Current Information    Return Home

Item # UFE-2493   $ 1,500

Full Image

CTD D20 Double Miter Saw

This machine is in Good Condition.

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Amber-CA-10-20-15/1512

MV-Sold-5-27-16    Return Home

Item # UFE-2494   $ 2,495

Full Image

CTD D45AX Double Miter Saw

This machine is in Good Condition.

Size:  12"

Machine Video: https://www.youtube.com/watch?v=GOBOGKwJtNs

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Diane-CA-10-20-15

SA-Sold-11-5-15   Return Home

Item # UFE-2495   $ 1,995

Full Image

CTD D45 Double Miter Saw

This machine is in Good Condition.

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Alonso-CA-10-30-15/1494

No Longer Available   Return Home

Item # UFE-2497   $ Call for Pricing

Full Image

CTD D45X Double Miter Saw

This machine is in Good Condition.

This item can be picked up in Missouri or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Rick-MO-11-3-15

See Page #354 for Current Information   Return Home