***Reduced***Item # UFE-1211   $775

Full Image

Dewalt 12" Compound Mitre Saws w/ Phaedra Miter-Grid

This machine is in Very Good Working Condition.

Dewalt 12" Saws / Phaedra Measuring System as shown.

This item can be picked up in the Connecticut, or shipped for an additional fee by UPS. Shipping is not the $6.50 default on the order page.

LIZ- CT-1-20-11 $795 / 1-25-12 $775

JP-Sold-2-10-12  Return Home

List $1,590

***Reduced***Item # UFE-1214   $625

Full Image

Frame Square Manual Joiner

This joiner is in Good Condition.

This item can be picked up in the New York, or shipped for an additional fee by UPS. Shipping is not the $6.50 default on the order page.

Jim-NY-1-27-11

Manufacturer's Information (for current generation):

(check with manufacturer for any differences between unit being offered and current generation machine)

comes with floor stand, cartridge v-nail feed & optional top with support bracket.

List Price $265

***Reduced***Item # UFE-1215   $125

Full Image

 Sold-7-16-13-Jim    Return Home

***Reduced***Item # UFE-1227   $2,995

Full Image

CTD D45A Double Miter Saw

This machine is in Good Working Condition. This machine has been well maintained. It is currently used to cut wood.

Below is information from Manufacturer's Website. Check with Tech Support for any differences between what is being sold and the newer generation machines.

From Manufacturer's Website:

CTD D45AX Fixed 45 Degree Frame Saw

The D45 is popular world wide because of its unique features, low cost and precision. Engineered for higher production, this double mitre saw makes two 45 degrees mitres at one time, saving time and materials. D45's are used by thousands in the decorative arts trade throughout world.

Designed to cut Aluminum, Wood, plastics, composites, aluminum extrusions, plastic extrusions, non-ferrous metals.

Blade Capacity: 10" OD (254mm) ,12'' OD, 14'' OD

Spindle & Pivot: Both mounted on pre-loaded and sealed ball bearings.

Arbor: 5/8 (16mm) with 2-1/4 (57mm) saw collars.

Iron Castings: Saw arm, pivot brackets and table are precision machined and ground with milled slots in table to guide pivot brackets and fences.

Motors & Voltages: 1-1/2 H.P., 3450 RPM with Dual Magnetic Starter.

Table Height: 34-1/2 (88cm) from floor.

Floor Stand: Close coupled heavy gage steel stand completely enclosed with 6 dust outlet. 1200 CFM required.

• Length of stroke adjustment: The D45AX is unique in that the stroke of the machine and the position of the blade above the work can be adjusted to use only the stroke needed to cut a particular moulding or extrusion. Saw heads reverse immediately, on release of the foot valve, thereby saving wasted time and motion.
   
• Production Rate: The D45AX is capable of cycling at one second intervals. However, actual production rates vary with the type and width of material to be cut.
   
• Size: Standard machine, without tables or gages; weight 550 lbs. 46'' wide x 22'' front to back x 51-1/2'' high.
   
• Actuation: Pneumatic foot valve with cover
   
• Air Pressure: 75 PSI with Air Filter/Regulator/Lubricator; includes Auto Drain.
   
• Air Consumption: 1.0 CF per 10 strokes at 75 PSI.

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Joseph-CA-2-4-11 $3,350 / 1-25-12 $2,995

See Page #180 for Current Information    Return Home

***Reduced***Item # UFE-1228   $2,995

Full Image

CTD D45A Double Miter Saw

This machine is in Good Working Condition. This machine has been well maintained. It is currently used to Polystyrene Mouldings.

Below is information from Manufacturer's Website. Check with Tech Support for any differences between what is being sold and the newer generation machines.

From Manufacturer's Website:

CTD D45AX Fixed 45 Degree Frame Saw

The D45 is popular world wide because of its unique features, low cost and precision. Engineered for higher production, this double mitre saw makes two 45 degrees mitres at one time, saving time and materials. D45's are used by thousands in the decorative arts trade throughout world.

Designed to cut Aluminum, Wood, plastics, composites, aluminum extrusions, plastic extrusions, non-ferrous metals.

Blade Capacity: 10" OD (254mm) ,12'' OD, 14'' OD

Spindle & Pivot: Both mounted on pre-loaded and sealed ball bearings.

Arbor: 5/8 (16mm) with 2-1/4 (57mm) saw collars.

Iron Castings: Saw arm, pivot brackets and table are precision machined and ground with milled slots in table to guide pivot brackets and fences.

Motors & Voltages: 1-1/2 H.P., 3450 RPM with Dual Magnetic Starter.

Table Height: 34-1/2 (88cm) from floor.

Floor Stand: Close coupled heavy gage steel stand completely enclosed with 6 dust outlet. 1200 CFM required.

• Length of stroke adjustment: The D45AX is unique in that the stroke of the machine and the position of the blade above the work can be adjusted to use only the stroke needed to cut a particular moulding or extrusion. Saw heads reverse immediately, on release of the foot valve, thereby saving wasted time and motion.
   
• Production Rate: The D45AX is capable of cycling at one second intervals. However, actual production rates vary with the type and width of material to be cut.
   
• Size: Standard machine, without tables or gages; weight 550 lbs. 46'' wide x 22'' front to back x 51-1/2'' high.
   
• Actuation: Pneumatic foot valve with cover
   
• Air Pressure: 75 PSI with Air Filter/Regulator/Lubricator; includes Auto Drain.
   
• Air Consumption: 1.0 CF per 10 strokes at 75 PSI.

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Joseph-CA-2-4-11 $3,350 / 1-25-12 $2,995

See Page #204 for Current Information    Return Home