***Reduced***Item # UFE-1228   $2,595 Or Make Offer

Full Image

CTD D45A Double Miter Saw

This machine is in Good Working Condition. This machine has been well maintained. It is currently used to Polystyrene Mouldings.

Below is information from Manufacturer's Website. Check with Tech Support for any differences between what is being sold and the newer generation machines.

From Manufacturer's Website:

CTD D45AX Fixed 45 Degree Frame Saw

The D45 is popular world wide because of its unique features, low cost and precision. Engineered for higher production, this double mitre saw makes two 45 degrees mitres at one time, saving time and materials. D45's are used by thousands in the decorative arts trade throughout world.

Designed to cut Aluminum, Wood, plastics, composites, aluminum extrusions, plastic extrusions, non-ferrous metals.

Blade Capacity: 10" OD (254mm) ,12'' OD, 14'' OD

Spindle & Pivot: Both mounted on pre-loaded and sealed ball bearings.

Arbor: 5/8 (16mm) with 2-1/4 (57mm) saw collars.

Iron Castings: Saw arm, pivot brackets and table are precision machined and ground with milled slots in table to guide pivot brackets and fences.

Motors & Voltages: 1-1/2 H.P., 3450 RPM with Dual Magnetic Starter.

Table Height: 34-1/2 (88cm) from floor.

Floor Stand: Close coupled heavy gage steel stand completely enclosed with 6 dust outlet. 1200 CFM required.

• Length of stroke adjustment: The D45AX is unique in that the stroke of the machine and the position of the blade above the work can be adjusted to use only the stroke needed to cut a particular moulding or extrusion. Saw heads reverse immediately, on release of the foot valve, thereby saving wasted time and motion.
   
• Production Rate: The D45AX is capable of cycling at one second intervals. However, actual production rates vary with the type and width of material to be cut.
   
• Size: Standard machine, without tables or gages; weight 550 lbs. 46'' wide x 22'' front to back x 51-1/2'' high.
   
• Actuation: Pneumatic foot valve with cover
   
• Air Pressure: 75 PSI with Air Filter/Regulator/Lubricator; includes Auto Drain.
   
• Air Consumption: 1.0 CF per 10 strokes at 75 PSI.

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Joseph-CA-2-4-11 $3,350 / 1-25-12 $2,995 / 11-12-12 $2,595

See Page #310 for Current Information    Return Home

***Reduced***Item # UFE-1229   $2,595 Or Make Offer

Full Image

CTD D45A Double Miter Saw

This machine is in Good Working Condition. This machine has been well maintained. It is has a 14" blade and is currently used to cut wood & polystyrene mouldings..

Below is information from Manufacturer's Website. Check with Tech Support for any differences between what is being sold and the newer generation machines.

From Manufacturer's Website:

CTD D45AX Fixed 45 Degree Frame Saw

The D45 is popular world wide because of its unique features, low cost and precision. Engineered for higher production, this double mitre saw makes two 45 degrees mitres at one time, saving time and materials. D45's are used by thousands in the decorative arts trade throughout world.

Designed to cut Aluminum, Wood, plastics, composites, aluminum extrusions, plastic extrusions, non-ferrous metals.

Blade Capacity: 10" OD (254mm) ,12'' OD, 14'' OD

Spindle & Pivot: Both mounted on pre-loaded and sealed ball bearings.

Arbor: 5/8 (16mm) with 2-1/4 (57mm) saw collars.

Iron Castings: Saw arm, pivot brackets and table are precision machined and ground with milled slots in table to guide pivot brackets and fences.

Motors & Voltages: 1-1/2 H.P., 3450 RPM with Dual Magnetic Starter.

Table Height: 34-1/2 (88cm) from floor.

Floor Stand: Close coupled heavy gage steel stand completely enclosed with 6 dust outlet. 1200 CFM required.

• Length of stroke adjustment: The D45AX is unique in that the stroke of the machine and the position of the blade above the work can be adjusted to use only the stroke needed to cut a particular moulding or extrusion. Saw heads reverse immediately, on release of the foot valve, thereby saving wasted time and motion.
   
• Production Rate: The D45AX is capable of cycling at one second intervals. However, actual production rates vary with the type and width of material to be cut.
   
• Size: Standard machine, without tables or gages; weight 550 lbs. 46'' wide x 22'' front to back x 51-1/2'' high.
   
• Actuation: Pneumatic foot valve with cover
   
• Air Pressure: 75 PSI with Air Filter/Regulator/Lubricator; includes Auto Drain.
   
• Air Consumption: 1.0 CF per 10 strokes at 75 PSI.

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Joseph-CA-2-4-11 $3,350 / 1-25-12 $2,995 / 8-17-12 $2,895 / 11-12-12 $2,595 s

See Page #310 for Current Information    Return Home

***Reduced***Item # UFE-1230   $2,595 Or Make Offer

Full Image

CTD D45A Double Miter Saw

This machine is in Good Working Condition. This machine has been well maintained. It is currently used to cut metal mouldings.

Below is information from Manufacturer's Website. Check with Tech Support for any differences between what is being sold and the newer generation machines.

From Manufacturer's Website:

CTD D45AX Fixed 45 Degree Frame Saw

The D45 is popular world wide because of its unique features, low cost and precision. Engineered for higher production, this double mitre saw makes two 45 degrees mitres at one time, saving time and materials. D45's are used by thousands in the decorative arts trade throughout world.

Designed to cut Aluminum, Wood, plastics, composites, aluminum extrusions, plastic extrusions, non-ferrous metals.

Blade Capacity: 10" OD (254mm) ,12'' OD, 14'' OD

Spindle & Pivot: Both mounted on pre-loaded and sealed ball bearings.

Arbor: 5/8 (16mm) with 2-1/4 (57mm) saw collars.

Iron Castings: Saw arm, pivot brackets and table are precision machined and ground with milled slots in table to guide pivot brackets and fences.

Motors & Voltages: 1-1/2 H.P., 3450 RPM with Dual Magnetic Starter.

Table Height: 34-1/2 (88cm) from floor.

Floor Stand: Close coupled heavy gage steel stand completely enclosed with 6 dust outlet. 1200 CFM required.

• Length of stroke adjustment: The D45AX is unique in that the stroke of the machine and the position of the blade above the work can be adjusted to use only the stroke needed to cut a particular moulding or extrusion. Saw heads reverse immediately, on release of the foot valve, thereby saving wasted time and motion.
   
• Production Rate: The D45AX is capable of cycling at one second intervals. However, actual production rates vary with the type and width of material to be cut.
   
• Size: Standard machine, without tables or gages; weight 550 lbs. 46'' wide x 22'' front to back x 51-1/2'' high.
   
• Actuation: Pneumatic foot valve with cover
   
• Air Pressure: 75 PSI with Air Filter/Regulator/Lubricator; includes Auto Drain.
   
• Air Consumption: 1.0 CF per 10 strokes at 75 PSI.

This item can be picked up in California or shipped for an additional fee by common carrier. Shipping is not the $6.50 default found in the shopping cart.

Joseph-CA-2-4-11 $3,350 / 1-25-12 $2,995 / 8-17-12 $2,895 / 11-12-12 $2,595 s

See Page #310 for Current Information    Return Home

   Item # UFE-1816   $375

Full Image

ITW AMP Miter Disc Sander

This machine is in Good Working Condition.

"From the Seller: Sander in very good condition. Used less than 500 times”

Manufacturer's Info:

With this tool, you can accurately true a corner by simply rotating the 12" sanding disc against the miter cut. This allows for perfect corners when joining and therefore a quality frame every time. Comes with a 45 degree template for accurate setting, Allen wrenches, a cleaning stick, sanding discs, and instruction manual. Weight 40 Lbs.

This item can be picked up in North Carolina or shipped for an additional fee by UPS. Shipping is not the $6.50 default found in the shopping cart.

Lewis/Tiffany-NC-11-13-12

MV-Sold-11-15-12  Return Home

***Reduced***Item # UFE-1738   $1,200

Full Image

Mitre Mite VN42 V-nailer

Mitre Mite VN42  V-Nail Frame Assembly Machine

This unit is in Good Condition.

Serial # 24,329

Manufactured in 1996-1997

"From the seller: The touch glue system is currently not functional. You may want to remove it or if it is cleaned up, it may still be functional. This unit has been in storage for a couple years an should lubricated. Contact ITW AMP tech support (Phil 847-821-7695) to learn how to lubricate before operating the first time”

This item can be picked up in Maryland or shipped for an additional fee by freight company. Shipping is not the $6.50 default on the order page.

Mike-MD-8-28-12 $1,250 / 11-14-12 $1,200/714

 MV-Sold-1-7-13   Return Home

(List price $6,400 +)

   *** Reduced***Item # UFE-1727   $2,825

Full Image

Mitre-Mite VN 4L Underpinner

This unit is in Good Condition. It also includes the stand.

ITW AMP Mitre Mite VN4 International

Seller bought new in 2005.

This item can be picked up in Virginia or shipped for an additional fee by a freight company. Shipping is not the $6.50 default on the order page.

David-VA-8-16-12 $2,995 / 9-6-12 $2,850 / 11-14-12 $2,825/708

JP-Sold-12-5-12  Return Home